| |
Main
Date: 04 Oct 2007 09:56:50
From: DaveH
Subject: Bent hanger --> Bent frame? ... shifting problems
|
[58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
Days ago I had a clipless newbie style slow-speed side crash which
bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
LBS straightened the hanger and replaced the bent der with a Dura Ace
rd-7700GS.
The new der shifted fine on the stand -- but on the road I
experienced problems, particularly when downshifting from 15 to 14
teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
erratic, not yielding to any amount of adjustment.
Rivendell suggested the frame may have been bent in the crash --
triangle pushed to the left. It looked like the hanger was bent
something on the order of 2-3 degrees -- wild visual guess.
Generally, how frequently is a bent hanger accompanied by a bent
frame? Tough question, I know. My immediate concern is whether I need
to find a shop that is equipped for frame checking and alignment.
I've read Sheldon and others regarding bent hangers and I've not seen
bent frames being mentioned as an associated issue, though the
possibility is obvious.
Dave
|
|
| |
Date: 07 Oct 2007 00:05:02
From: Vee
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Oct 6, 10:48 am, DaveH <ddhartw...@FUTILITYearthlink.net > wrote:
> >> I'm guessing I can find a frame man near Wash DC, 2 hours away.
> >> It is tempting to try the FAQ's manual straightening method. I think
> >> the rear-end needs to be pulled to the right ~1/16".
> >> Dave
>
> >I'd take it too him if you can; trying to fix it on your own without
> >any prior experience suggests that you might wind up ruining the
> >frame. sometimes it pays to have the job done right even if you have
> >to pay someone else to do it. It sounds like you would appreciate a
> >good job well done- it might be a 2hr drive for you, but surely you
> >spend much more time than that weekly riding your bike and when you do
> >your mind should be free of issues regarding your frames alignment
>
> Yes, of course -- you are right.
>
> There's something about a bent frame--even if minor and rideable--that
> is terribly bothersome. Chips, nicks and other flaws aren't an issue.
> Even mechs that are not perfect. But the frame is the soul of the
> machine, and a bent one on a bike like this Riv Rambouillet is rather
> heartbreaking, frankly.
>
> Maybe that's going over the deep end, but after riding a bike for many
> miles, it becomes an extension of the body.
> Dave
The evil bike mechanic on my shoulder just muttered "I don't know,
princess... 1/16" is an awfully small pea."
-Vee
|
| | |
Date: 07 Oct 2007 21:14:59
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>> Maybe that's going over the deep end, but after riding a bike for many
>> miles, it becomes an extension of the body.
>> Dave
>
>The evil bike mechanic on my shoulder just muttered "I don't know,
>princess... 1/16" is an awfully small pea."
>
>-Vee
Evil yes, but quality evil -- which makes all the difference.
Dave
|
| |
Date: 05 Oct 2007 20:01:13
From:
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Oct 5, 9:42 pm, DaveH <ddhartw...@FUTILITYearthlink.net > wrote:
> >DaveH wrote:
> >> I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
> >> with my Sugino XD-2 48/36/36 crank since the problem is worst on the
> >> largest chainring, though I know that can be typical.
>
> >Crank's not the problem.
>
> I replaced the DA 7700gs rear derailleur with a new Ultegra 6500gs.
> It now shifts perfectly. Smoother, more incisive -- it is a mystery.
>
> Now I must solve the bent frame problem. No hands it veers right,
> requiring a slight left body lean to maintain a straight line. I had
> an experienced friend confirm this. Mild, not terminal, but
> psychologically intolerable.
>
> I'm guessing I can find a frame man near Wash DC, 2 hours away.
> It is tempting to try the FAQ's manual straightening method. I think
> the rear-end needs to be pulled to the right ~1/16".
> Dave
I'd take it too him if you can; trying to fix it on your own without
any prior experience suggests that you might wind up ruining the
frame. sometimes it pays to have the job done right even if you have
to pay someone else to do it. It sounds like you would appreciate a
good job well done- it might be a 2hr drive for you, but surely you
spend much more time than that weekly riding your bike and when you do
your mind should be free of issues regarding your frames alignment
|
| | |
Date: 06 Oct 2007 11:48:48
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>> I'm guessing I can find a frame man near Wash DC, 2 hours away.
>> It is tempting to try the FAQ's manual straightening method. I think
>> the rear-end needs to be pulled to the right ~1/16".
>> Dave
>
>I'd take it too him if you can; trying to fix it on your own without
>any prior experience suggests that you might wind up ruining the
>frame. sometimes it pays to have the job done right even if you have
>to pay someone else to do it. It sounds like you would appreciate a
>good job well done- it might be a 2hr drive for you, but surely you
>spend much more time than that weekly riding your bike and when you do
>your mind should be free of issues regarding your frames alignment
Yes, of course -- you are right.
There's something about a bent frame--even if minor and rideable--that
is terribly bothersome. Chips, nicks and other flaws aren't an issue.
Even mechs that are not perfect. But the frame is the soul of the
machine, and a bent one on a bike like this Riv Rambouillet is rather
heartbreaking, frankly.
Maybe that's going over the deep end, but after riding a bike for many
miles, it becomes an extension of the body.
Dave
|
| |
Date: 04 Oct 2007 15:57:48
From: A Muzi
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
DaveH wrote:
> [58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
>
> Days ago I had a clipless newbie style slow-speed side crash which
> bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
> LBS straightened the hanger and replaced the bent der with a Dura Ace
> rd-7700GS.
>
> The new der shifted fine on the stand -- but on the road I
> experienced problems, particularly when downshifting from 15 to 14
> teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
> erratic, not yielding to any amount of adjustment.
>
> Rivendell suggested the frame may have been bent in the crash --
> triangle pushed to the left. It looked like the hanger was bent
> something on the order of 2-3 degrees -- wild visual guess.
>
> Generally, how frequently is a bent hanger accompanied by a bent
> frame? Tough question, I know. My immediate concern is whether I need
> to find a shop that is equipped for frame checking and alignment.
>
> I've read Sheldon and others regarding bent hangers and I've not seen
> bent frames being mentioned as an associated issue, though the
> possibility is obvious.
Much more likely to be a simple error/oversight; derailleur
alignment/adjustment/cable problem. You should be able to return to the
shop which 'upgraded' your gear system and watch the Campagnolo "R" tool
alignment then a full frame alignment gauge. If the rear end were off to
one side enough to give shifting problems, you'd likely have noticed a
difference when riding no hands.
p.s. if there are plastic ferrules on your casing, have them replaced
with real ones.
--
Andrew Muzi
www.yellowjersey.org
Open every day since 1 April, 1971
|
| | |
Date: 05 Oct 2007 09:40:41
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Thu, 04 Oct 2007 15:57:48 -0500, A Muzi <am@yellowjersey.org >
wrote:
>DaveH wrote:
>> [58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
>>
>> Days ago I had a clipless newbie style slow-speed side crash which
>> bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
>> LBS straightened the hanger and replaced the bent der with a Dura Ace
>> rd-7700GS.
>>
>> The new der shifted fine on the stand -- but on the road I
>> experienced problems, particularly when downshifting from 15 to 14
>> teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
>> erratic, not yielding to any amount of adjustment.
>>
>> Rivendell suggested the frame may have been bent in the crash --
>> triangle pushed to the left. It looked like the hanger was bent
>> something on the order of 2-3 degrees -- wild visual guess.
>>
>> Generally, how frequently is a bent hanger accompanied by a bent
>> frame? Tough question, I know. My immediate concern is whether I need
>> to find a shop that is equipped for frame checking and alignment.
>>
>> I've read Sheldon and others regarding bent hangers and I've not seen
>> bent frames being mentioned as an associated issue, though the
>> possibility is obvious.
>
>Much more likely to be a simple error/oversight; derailleur
>alignment/adjustment/cable problem. You should be able to return to the
>shop which 'upgraded' your gear system and watch the Campagnolo "R" tool
>alignment then a full frame alignment gauge. If the rear end were off to
>one side enough to give shifting problems, you'd likely have noticed a
>difference when riding no hands.
>p.s. if there are plastic ferrules on your casing, have them replaced
>with real ones.
I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
with my Sugino XD-2 48/36/36 crank since the problem is worst on the
largest chainring, though I know that can be typical.
|
| | | |
Date: 05 Oct 2007 14:08:59
From: A Muzi
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>> DaveH wrote:
>>> [58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
>>> Days ago I had a clipless newbie style slow-speed side crash which
>>> bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
>>> LBS straightened the hanger and replaced the bent der with a Dura Ace
>>> rd-7700GS.
>>> The new der shifted fine on the stand -- but on the road I
>>> experienced problems, particularly when downshifting from 15 to 14
>>> teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
>>> erratic, not yielding to any amount of adjustment.
>>> Rivendell suggested the frame may have been bent in the crash --
>>> triangle pushed to the left. It looked like the hanger was bent
>>> something on the order of 2-3 degrees -- wild visual guess.
>>> Generally, how frequently is a bent hanger accompanied by a bent
>>> frame? Tough question, I know. My immediate concern is whether I need
>>> to find a shop that is equipped for frame checking and alignment.
>>> I've read Sheldon and others regarding bent hangers and I've not seen
>>> bent frames being mentioned as an associated issue, though the
>>> possibility is obvious.
> A Muzi <am@yellowjersey.org> wrote:
>> Much more likely to be a simple error/oversight; derailleur
>> alignment/adjustment/cable problem. You should be able to return to the
>> shop which 'upgraded' your gear system and watch the Campagnolo "R" tool
>> alignment then a full frame alignment gauge. If the rear end were off to
>> one side enough to give shifting problems, you'd likely have noticed a
>> difference when riding no hands.
>> p.s. if there are plastic ferrules on your casing, have them replaced
>> with real ones.
DaveH wrote:
> I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
> with my Sugino XD-2 48/36/36 crank since the problem is worst on the
> largest chainring, though I know that can be typical.
Crank's not the problem.
--
Andrew Muzi
www.yellowjersey.org
Open every day since 1 April, 1971
|
| | | | |
Date: 05 Oct 2007 21:42:54
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>DaveH wrote:
>> I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
>> with my Sugino XD-2 48/36/36 crank since the problem is worst on the
>> largest chainring, though I know that can be typical.
>
>Crank's not the problem.
I replaced the DA 7700gs rear derailleur with a new Ultegra 6500gs.
It now shifts perfectly. Smoother, more incisive -- it is a mystery.
Now I must solve the bent frame problem. No hands it veers right,
requiring a slight left body lean to maintain a straight line. I had
an experienced friend confirm this. Mild, not terminal, but
psychologically intolerable.
I'm guessing I can find a frame man near Wash DC, 2 hours away.
It is tempting to try the FAQ's manual straightening method. I think
the rear-end needs to be pulled to the right ~1/16".
Dave
|
| | | | | |
Date: 05 Oct 2007 21:11:20
From: A Muzi
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>> DaveH wrote:
>>> I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
>>> with my Sugino XD-2 48/36/36 crank since the problem is worst on the
>>> largest chainring, though I know that can be typical.
>> Crank's not the problem.
DaveH wrote:
> I replaced the DA 7700gs rear derailleur with a new Ultegra 6500gs.
> It now shifts perfectly. Smoother, more incisive -- it is a mystery.
>
> Now I must solve the bent frame problem. No hands it veers right,
> requiring a slight left body lean to maintain a straight line. I had
> an experienced friend confirm this. Mild, not terminal, but
> psychologically intolerable.
>
> I'm guessing I can find a frame man near Wash DC, 2 hours away.
> It is tempting to try the FAQ's manual straightening method. I think
> the rear-end needs to be pulled to the right ~1/16".
Good guess, but I'd look for a place where you can watch steel gauges on
the frame before you start pulling on the rear end.
--
Andrew Muzi
www.yellowjersey.org
Open every day since 1 April, 1971
|
| | | | | | |
Date: 06 Oct 2007 11:34:24
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
>> I'm guessing I can find a frame man near Wash DC, 2 hours away.
>> It is tempting to try the FAQ's manual straightening method. I think
>> the rear-end needs to be pulled to the right ~1/16".
>
>Good guess, but I'd look for a place where you can watch steel gauges on
>the frame before you start pulling on the rear end.
Of course, lest I make the situation worse. Thanks --
Dave
|
| | | |
Date: 05 Oct 2007 11:40:42
From: Peter Cole
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
DaveH wrote:
> On Thu, 04 Oct 2007 15:57:48 -0500, A Muzi <am@yellowjersey.org>
> wrote:
>
>> DaveH wrote:
>>> [58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
>>>
>>> Days ago I had a clipless newbie style slow-speed side crash which
>>> bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
>>> LBS straightened the hanger and replaced the bent der with a Dura Ace
>>> rd-7700GS.
>>>
>>> The new der shifted fine on the stand -- but on the road I
>>> experienced problems, particularly when downshifting from 15 to 14
>>> teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
>>> erratic, not yielding to any amount of adjustment.
>>>
>>> Rivendell suggested the frame may have been bent in the crash --
>>> triangle pushed to the left. It looked like the hanger was bent
>>> something on the order of 2-3 degrees -- wild visual guess.
>>>
>>> Generally, how frequently is a bent hanger accompanied by a bent
>>> frame? Tough question, I know. My immediate concern is whether I need
>>> to find a shop that is equipped for frame checking and alignment.
>>>
>>> I've read Sheldon and others regarding bent hangers and I've not seen
>>> bent frames being mentioned as an associated issue, though the
>>> possibility is obvious.
>> Much more likely to be a simple error/oversight; derailleur
>> alignment/adjustment/cable problem. You should be able to return to the
>> shop which 'upgraded' your gear system and watch the Campagnolo "R" tool
>> alignment then a full frame alignment gauge. If the rear end were off to
>> one side enough to give shifting problems, you'd likely have noticed a
>> difference when riding no hands.
>> p.s. if there are plastic ferrules on your casing, have them replaced
>> with real ones.
>
> I wonder if the Dura Ace 7700gs triple rear derailleur is incompatible
> with my Sugino XD-2 48/36/36 crank since the problem is worst on the
> largest chainring, though I know that can be typical.
>
Doesn't sound likely. Does the DA rear have a weaker spring than the
original? Sluggish shifting to smaller sprockets is usually because the
spring is too light for the friction in the path.
|
| |
Date: 04 Oct 2007 11:23:49
From: Art Harris
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
DaveH wrote:
> Rivendell suggested the frame may have been bent in the crash --
> triangle pushed to the left. It looked like the hanger was bent
> something on the order of 2-3 degrees -- wild visual guess.
Try the "string test" to check frame alignment:
http://sheldonbrown.com/frame-spacing.html
(scroll down near the bottom)
Also make sure the shift wire is anchored at the correct place on the
derailleur.
Art Harris
|
| | |
Date: 04 Oct 2007 15:29:16
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Thu, 04 Oct 2007 11:23:49 -0700, Art Harris <n2ah@hotmail.com >
wrote:
>DaveH wrote:
>> Rivendell suggested the frame may have been bent in the crash --
>> triangle pushed to the left. It looked like the hanger was bent
>> something on the order of 2-3 degrees -- wild visual guess.
>
>Try the "string test" to check frame alignment:
>
>http://sheldonbrown.com/frame-spacing.html
>(scroll down near the bottom)
>
>Also make sure the shift wire is anchored at the correct place on the
>derailleur.
>
>Art Harris
Art,
Please see my latest post in the original thread.
Thanks -- Dave
|
| |
Date: 04 Oct 2007 16:22:48
From: M-gineering
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
DaveH wrote:
> [58 cm Rivendell Ramboulliet -- steel frame, Dura Ace bar ends]
>
> Days ago I had a clipless newbie style slow-speed side crash which
> bent the derailleur hanger and the Ultegra rd-6500gs triple der. My
> LBS straightened the hanger and replaced the bent der with a Dura Ace
> rd-7700GS.
>
> The new der shifted fine on the stand -- but on the road I
> experienced problems, particularly when downshifting from 15 to 14
> teeth cogs (Ultegra 12-27, 9 sp cassette). The prob seems to be
> erratic, not yielding to any amount of adjustment.
>
> Rivendell suggested the frame may have been bent in the crash --
> triangle pushed to the left. It looked like the hanger was bent
> something on the order of 2-3 degrees -- wild visual guess.
>
> Generally, how frequently is a bent hanger accompanied by a bent
> frame? Tough question, I know. My immediate concern is whether I need
> to find a shop that is equipped for frame checking and alignment.
>
> I've read Sheldon and others regarding bent hangers and I've not seen
> bent frames being mentioned as an associated issue, though the
> possibility is obvious.
> Dave
Bent frame isn't very likely with just toppling over. If you can ride
the frame no handed without the frame veering left or right it's fine.
I'd investigate free movement of the shiftercable first. Is the cable
properly located underneath the bracket? Last bit of outer cable not to
short, kinked, badly cut. missing ferrule etc? And another good one:
cable properly clamped in the groove on the derailleur body?
--
/Marten
info(apestaartje)m-gineering(punt)nl
|
| | |
Date: 04 Oct 2007 17:51:02
From: still me
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Thu, 04 Oct 2007 16:22:48 -0700, M-gineering
<ikmotgeenspam@m-gineering.nl > wrote:
>Bent frame isn't very likely with just toppling over. If you can ride
>the frame no handed without the frame veering left or right it's fine.
>I'd investigate free movement of the shiftercable first. Is the cable
>properly located underneath the bracket? Last bit of outer cable not to
>short, kinked, badly cut. missing ferrule etc? And another good one:
>cable properly clamped in the groove on the derailleur body?
Not to mention, bent frames are more likely to affect the movement at
the limits, not in the middle of the cog. It's possible, but I would
think the bend would have to be severe for that to happen.
How good a job did they do on the hanger straightening? Any chance
they left it "non flat" ?
|
| | | |
Date: 04 Oct 2007 15:27:53
From: DaveH
Subject: Re: Bent hanger --> Bent frame? ... shifting problems
|
On Thu, 04 Oct 2007 17:51:02 GMT, still me <wheeledBob@yahoo.com >
wrote:
>On Thu, 04 Oct 2007 16:22:48 -0700, M-gineering
><ikmotgeenspam@m-gineering.nl> wrote:
>
>>Bent frame isn't very likely with just toppling over. If you can ride
>>the frame no handed without the frame veering left or right it's fine.
>>I'd investigate free movement of the shiftercable first. Is the cable
>>properly located underneath the bracket? Last bit of outer cable not to
>>short, kinked, badly cut. missing ferrule etc? And another good one:
>>cable properly clamped in the groove on the derailleur body?
>
>Not to mention, bent frames are more likely to affect the movement at
>the limits, not in the middle of the cog. It's possible, but I would
>think the bend would have to be severe for that to happen.
>
>How good a job did they do on the hanger straightening? Any chance
>they left it "non flat" ?
Marten and Still,
I did the string test for rear triangle displacement at:
http://www.faqs.org/faqs/bicycles-faq/part3/section-50.html
The test indicates the seat tube deviates to the right by 1/16". This
suggests the rear tri is displaced 1/32" to the left. This doesn't
sound like much; but indeed, I just did some extensive no-hands riding
and there is a mild but distinct tendency to veer to the right.
I thought something didn't feel right about the ride feel before a
bent frame even occurred to me but it was a bit vague and assumed it
was my imagination.
Still, you would not think this would be enough to effect shifting,
especially in the middle cogs as noted. I talked to Rivendell and they
agree with this.
Regarding hanger straightening: The LBS appeared to take his time with
what is obviously a special tool. I must assume at this point that
it's ok.
Regarding cable issues Marten: Everything's ok, as far as I can tell.
Not sure what to do. I'm tempted to put an Ultegra derailleur back on
it.
I live in the sticks and this LBS is not equipped to straighten
frames. The FAQ page suggests manual straightening. Not crazy about
that idea. I'll figure it all out.
Dave
|
|
