| |
Main
Date: 08 Aug 2007 12:57:22
From: Carl Sundquist
Subject: Infernal cable question
|
My primary bike is an 11 year old Corima that has internal cable routing for
the shifting. The shifting has gotten absolutely horrible. Seemingly
whenever there could be any moisture present, the effort needed to move the
right hand upshift paddle becomes incredibly hard. This has been going on
all year. Until very recently, the downshifts were not exactly crisp, but
certainly did not reflect an equivalent binding or force to allow the
derailleur to move. Since Sunday, I can click down through the gears and the
cable end will stick out the front of the "brifter". It will then gradually,
over a period of minutes, shift down to the selected cog.
For the longest time I used the Gore cables, but you can't find them any
more. I have sprayed Tri-flow into the internal housing to aid in the
slipperiness and also blown air through the housing to clean out any when
I've changed the actual cable wire. I also use the teflon coated Jagwire.
I've changed/fiddled with it at least three times already this year with
only temporary, modest improvement.
I can understand if the Tri-flow gradually caused the ID of the housing to
swell, but the binding is inconsistent.
Thoughts, suggestions?
|
|
| |
Date: 08 Aug 2007 17:30:45
From: A Muzi
Subject: Re: Infernal cable question
|
Carl Sundquist wrote:
> My primary bike is an 11 year old Corima that has internal cable routing
> for the shifting. The shifting has gotten absolutely horrible. Seemingly
> whenever there could be any moisture present, the effort needed to move
> the right hand upshift paddle becomes incredibly hard. This has been
> going on all year. Until very recently, the downshifts were not exactly
> crisp, but certainly did not reflect an equivalent binding or force to
> allow the derailleur to move. Since Sunday, I can click down through the
> gears and the cable end will stick out the front of the "brifter". It
> will then gradually, over a period of minutes, shift down to the
> selected cog.
>
> For the longest time I used the Gore cables, but you can't find them any
> more. I have sprayed Tri-flow into the internal housing to aid in the
> slipperiness and also blown air through the housing to clean out any
> when I've changed the actual cable wire. I also use the teflon coated
> Jagwire. I've changed/fiddled with it at least three times already this
> year with only temporary, modest improvement.
>
> I can understand if the Tri-flow gradually caused the ID of the housing
> to swell, but the binding is inconsistent.
New 5mm gear casing with new wires (Campagnolo are nice, others can be
good) wiped with oil on installation will shift crisply for a good long
while. Use metal casing caps of the appropriate dimension - they are
_not_ all the same!
4mm casing, plastic casing end caps, corrosion all degrade shift response.
Your TriFlow is rinsing off whatever lubrication was there, making it
rust faster.
--
Andrew Muzi
www.yellowjersey.org
Open every day since 1 April, 1971
|
| |
Date: 08 Aug 2007 11:28:15
From: Nate Knutson
Subject: Re: Infernal cable question
|
On Aug 8, 10:57 am, "Carl Sundquist" <carl...@cox.net > wrote:
> My primary bike is an 11 year old Corima that has internal cable routing for
> the shifting. The shifting has gotten absolutely horrible. Seemingly
> whenever there could be any moisture present, the effort needed to move the
> right hand upshift paddle becomes incredibly hard. This has been going on
> all year. Until very recently, the downshifts were not exactly crisp, but
> certainly did not reflect an equivalent binding or force to allow the
> derailleur to move. Since Sunday, I can click down through the gears and the
> cable end will stick out the front of the "brifter". It will then gradually,
> over a period of minutes, shift down to the selected cog.
>
> For the longest time I used the Gore cables, but you can't find them any
> more. I have sprayed Tri-flow into the internal housing to aid in the
> slipperiness and also blown air through the housing to clean out any when
> I've changed the actual cable wire. I also use the teflon coated Jagwire.
> I've changed/fiddled with it at least three times already this year with
> only temporary, modest improvement.
>
> I can understand if the Tri-flow gradually caused the ID of the housing to
> swell, but the binding is inconsistent.
>
> Thoughts, suggestions?
Your internal routing is the more common setup where you've got a
normal full cable housing through the frame, either inside an internal
sleeve tube or just through the frame tube, correct? If so, have you
tried replacing the housing?
|
| | |
Date: 09 Aug 2007 07:24:35
From: Joel Mayes
Subject: Re: Infernal cable question
|
On 2007-08-08, Nate Knutson <bikenate@riseup.net > wrote:
> On Aug 8, 10:57 am, "Carl Sundquist" <carl...@cox.net> wrote:
>> Thoughts, suggestions?
>
> Your internal routing is the more common setup where you've got a
> normal full cable housing through the frame, either inside an internal
> sleeve tube or just through the frame tube, correct? If so, have you
> tried replacing the housing?
I tip for the OP, when you do this don't pull the old outer cable out of
the tube, use strong fishing line to tie the old and new outers cables
together then pull the new cable through as you pull the old cable out.
Cheers
Joel
--
Human Powered Cycles
|
| | | |
Date: 09 Aug 2007 09:03:02
From: Bill Sornson
Subject: Re: Infernal cable question
|
Joel Mayes wrote:
> On 2007-08-08, Nate Knutson <bikenate@riseup.net> wrote:
>> On Aug 8, 10:57 am, "Carl Sundquist" <carl...@cox.net> wrote:
>
>>> Thoughts, suggestions?
>>
>> Your internal routing is the more common setup where you've got a
>> normal full cable housing through the frame, either inside an
>> internal sleeve tube or just through the frame tube, correct? If so,
>> have you tried replacing the housing?
>
> I tip for the OP, when you do this don't pull the old outer cable out
> of the tube, use strong fishing line to tie the old and new outers
> cables together then pull the new cable through as you pull the old
> cable out.
Even easier is to just use a "guide tube" that fits inside the holes and is
longer than their span.
|
|
