| |
Main
Date: 29 Jun 2007 16:22:27
From: zencycle
Subject: determining correct BB spindle length
|
How does one determine what bottom bracket spindle length to get? I'm
asking what I need to measure on the bike to make sure I get a length
that will give me a good chainline.This is for a newer road racing
frame that had no bottom bracket when I got it so I have nothing to
compare it to. I'm using a square taper crankset (FSA carbon) and have
found FSA ultimax BBs online at reasonable prices. I would prefer
having the big chainring line up with middle of the cogset. Is there a
measurement or combination of measurements I can make to come to a
reasonable number?
|
|
| |
Date: 29 Jun 2007 18:14:24
From: zencycle
Subject: Re: determining correct BB spindle length
|
On Jun 29, 1:58 pm, A Muzi <a...@yellowjersey.org > wrote:
> zencycle wrote:
> > How does one determine what bottom bracket spindle length to get? I'm
> > asking what I need to measure on the bike to make sure I get a length
> > that will give me a good chainline.This is for a newer road racing
> > frame that had no bottom bracket when I got it so I have nothing to
> > compare it to. I'm using a square taper crankset (FSA carbon) and have
> > found FSA ultimax BBs online at reasonable prices. I would prefer
> > having the big chainring line up with middle of the cogset. Is there a
> > measurement or combination of measurements I can make to come to a
> > reasonable number?
>
> The usual litany-
> Thread matches frame, spindle matches crank.
> FSA singles are 108, doubles 113, triples 118 all symmetric.
>
> Yes, that is counterintuitive (you'd expect that 5mm overall on a
> symmetric spindle would add only 2.5mm per side). Crank designers have a
> wide latitude of choices about the relationship of spindle to rings to
> pedal. You can't look at an unknown crank and 'see' the spindle length
> readily.
> --
> Andrew Muziwww.yellowjersey.org
> Open every day since 1 April, 1971
Except that they offer the ultimax in six different sizes. I tried a
Specialized 113 I had lying around but the chainline ended up with the
big ring lined up on the 14 (12x23 9sp) and I couldn't push the
'fixed' cup side any further into the BB shell, but i'm thinking the
103 they offer would be a bit short. I don't want to spend $100 on yet
_another_ bike part I'll never use.This is why I was hoping for some
sort of silly measurement like 'hub spacing times .75 +\- Xmm times
the number of cogs you want to offset....' or some shit like
that.Since this is a JIS standard, is there a spec regarding how far
into the crank arm the spindle is supposed to seat?
|
| |
Date: 29 Jun 2007 18:03:35
From: zencycle
Subject: Re: determining correct BB spindle length
|
On Jun 29, 12:45 pm, Nate Knutson <biken...@riseup.net > wrote:
> On Jun 29, 9:22 am, zencycle <zency...@bikerider.com> wrote:
>
> > How does one determine what bottom bracket spindle length to get? I'm
> > asking what I need to measure on the bike to make sure I get a length
> > that will give me a good chainline.This is for a newer road racing
> > frame that had no bottom bracket when I got it so I have nothing to
> > compare it to. I'm using a square taper crankset (FSA carbon) and have
> > found FSA ultimax BBs online at reasonable prices. I would prefer
> > having the big chainring line up with middle of the cogset. Is there a
> > measurement or combination of measurements I can make to come to a
> > reasonable number?
>
> In your case, the crank is recent enough that you should be able to
> dig up a recommended spindle length. FSA can probably tell you pretty
> quickly if you call them. Recommended spindle lengths are a length
> chosen to give decent chainline when used alongside the rear
> drivetrain parts the crank is intended for, ie a 130-spaced road hub
> in your case. The trick with recommended spindle lengths is that
> sometimes they'd be a little longer than would give optimal chainline,
> in order to pre-emptively work around the many frames with clearance
> issues.
Thanks, I actually posted the question to their tech support before I
posted here, but whoi knows when/if I'll hear back.
|
| |
Date: 29 Jun 2007 12:58:20
From: A Muzi
Subject: Re: determining correct BB spindle length
|
zencycle wrote:
> How does one determine what bottom bracket spindle length to get? I'm
> asking what I need to measure on the bike to make sure I get a length
> that will give me a good chainline.This is for a newer road racing
> frame that had no bottom bracket when I got it so I have nothing to
> compare it to. I'm using a square taper crankset (FSA carbon) and have
> found FSA ultimax BBs online at reasonable prices. I would prefer
> having the big chainring line up with middle of the cogset. Is there a
> measurement or combination of measurements I can make to come to a
> reasonable number?
>
The usual litany-
Thread matches frame, spindle matches crank.
FSA singles are 108, doubles 113, triples 118 all symmetric.
Yes, that is counterintuitive (you'd expect that 5mm overall on a
symmetric spindle would add only 2.5mm per side). Crank designers have a
wide latitude of choices about the relationship of spindle to rings to
pedal. You can't look at an unknown crank and 'see' the spindle length
readily.
--
Andrew Muzi
www.yellowjersey.org
Open every day since 1 April, 1971
|
| |
Date: 29 Jun 2007 09:45:40
From: Nate Knutson
Subject: Re: determining correct BB spindle length
|
On Jun 29, 9:22 am, zencycle <zency...@bikerider.com > wrote:
> How does one determine what bottom bracket spindle length to get? I'm
> asking what I need to measure on the bike to make sure I get a length
> that will give me a good chainline.This is for a newer road racing
> frame that had no bottom bracket when I got it so I have nothing to
> compare it to. I'm using a square taper crankset (FSA carbon) and have
> found FSA ultimax BBs online at reasonable prices. I would prefer
> having the big chainring line up with middle of the cogset. Is there a
> measurement or combination of measurements I can make to come to a
> reasonable number?
In your case, the crank is recent enough that you should be able to
dig up a recommended spindle length. FSA can probably tell you pretty
quickly if you call them. Recommended spindle lengths are a length
chosen to give decent chainline when used alongside the rear
drivetrain parts the crank is intended for, ie a 130-spaced road hub
in your case. The trick with recommended spindle lengths is that
sometimes they'd be a little longer than would give optimal chainline,
in order to pre-emptively work around the many frames with clearance
issues.
|
|
